Filter Products
MillRight CNC M3 Kit Bundle
MillRight CNC M3 Kit Bundle
MillRight CNC M3 Kit Bundle

Product Info

Software is not included but everything you need is available for FREE. See the FAQ page.

Capabilities:
Mills wood, plastic, foam, carbon fiber, circuit boards, and soft metals.

Working Area:
Over 10.25”×10.25”×2”  (260mm × 260mm × 50mm)

What’s included:
All the hardware items you need to get going. You get the machine parts kit, a DeWalt DWP611 router, router mount, an end mill, and basic clamps.

Shipping:

Shipping on this item starts at $29 domestic and increases based on options and other products added. The total will be calculated in your shopping cart.

Refund Policy and Product Warranty

Full refunds available for orders that are canceled prior to shipment. We will replace any part that may become defective within 90 days of shipment.

 

$499.00 – $679.00 Select options
MillRight CNC Carve King Kit Bundle
MillRight CNC Carve King Kit Bundle
MillRight CNC Carve King Kit Bundle

Product Info

Software is not included but everything you need is available for FREE. See the FAQ page.

Capabilities:
Mills wood, plastic, foam, carbon fiber, circuit boards, and soft metals. This machine can make higher precision and more aggressive cuts than our M3.

Working Area:
Approximately 17.25”×17.25”×4”

Footprint:
On table footprint of 25″×30″, counting the 4″ inch square electronics enclosure that goes at the back left. With overhands of motors above the table it is 28″×30″×17″.

What’s included:
All the hardware items you need to get going. You get the machine parts kit, a DeWalt DWP611 router, router mount, an end mill, and basic clamps.

Warranty

There is a 90-day warranty on this product. No returns or cancellations are permitted once the order has left our facility.

We provide free technical support for this product.

$869.00 – $1,039.00 Select options
MillRight CNC Power Route Kit Bundle
MillRight CNC Power Route Kit Bundle
MillRight CNC Power Route Kit Bundle

Product Info

Capabilities:
Mills wood, plastic, foam, carbon fiber, circuit boards, soft metals, and can make occasional light cuts in hard metals. This machine is our most precise and has material removal rates of up to 15 times that of our other machines.

Working Area:
Approximately 25”×25”×5”

Footprint:
About 39″ deep × 49″ wide by 29″ high. 12″ of the width is the electronics enclosure that sits to the left side. 5″ of the depth comes from the Y motor on the front that is above the table surface.

Warranty

There is a 180-day warranty on this product. No returns or cancellations are permitted once the order has left our facility.

We provide free technical support for this product.

Shipping

We are currently experiencing high sales volume of the Power Route. Lead time is about two weeks. Due to its size and weight, the website only calculates shipping on the Power Route to the contiguous 48 United States at this time. Please contact sales@millrightcnc.com if you want to make an arrangement for other shipping locations.

Software is not included but everything you need is available for FREE. See the FAQ page.

$2,795.00 – $2,999.00 Select options
Sale!
MillRight CNC Power Route XL Assembled
MillRight CNC Power Route XL Assembled
MillRight CNC Power Route XL Assembled

Product Info

Capabilities:
Mills wood, plastic, foam, carbon fiber, circuit boards, soft metals, and can make occasional light cuts in hard metals. This machine is our largest and most precise. It has material removal rates of up to 15 times that of our other machines.

Working Area:
Approximately 49.5”×49.5”×5”

Footprint:
69″ wide x 66″ deep x 49″ inches high and weighs about 450 pounds

Warranty

There is a 180-day parts only warranty on this product. No returns or cancellations are permitted once the order has left our facility.

We provide free technical support for this product.

Shipping

Lead time to shipment is two weeks. Due to its size and weight, this machine must ship truck freight. The website will charge $500 for truck freight. Actual freight will differ. We will refund or collect the difference prior to shipping. Please contact sales@millrightcnc.com if you want an exact shipping quote before ordering.

 

$5,649.00 $5,549.00 Add to cart
5 Axis Mill
5 Axis Mill
5 Axis Mill

Product Info

Motion type:
Capable of simultaneous 5 axis positioning

Capabilities:
Mills wood, plastic, foam, aluminum, brass, and other soft metals.

Working Area:
Approximately 23.5”×18″×5.5”

Warranty

There is a 180-day warranty on this product. No returns or cancellations are permitted once the order has left our facility.

We provide free technical (functionality) support for this product. We do not provide applications support. Please make sure you have the resources at your disposal for learning five axis setups, toolpathing, and machining techniques.

Shipping

FREIGHT MUST BE QUOTED ON THIS ITEM. CONTACT SALES@MILLRIGHTCNC.COM FOR A FREIGHT QUOTE. IF YOU CHECK OUT VIA THE WEBSITE WE WILL CONTACT YOU TO ADJUST  AND COLLECT FOR THE ACTUAL COST. SHIPPING CAN RANGE FROM $175 TO $900 DEPENDING ON YOUR LOCATION AND TRUCKING ACCESS.

There is a 4 week lead time on this machine.

 

$3,849.00 Add to cart
Premium 7 Watt Laser Kit
Premium 7 Watt Laser Kit
Premium 7 Watt Laser Kit

This is the new 7 watt diode laser from JTECH Photonics. The JTECH team has carefully designed these to deliver excellent performance and quality. They integrate directly into any of our machines. Engrave on wood, leather, acrylics, and many other materials … Read More

$599.00 Select options
17″ Manual Lathe with Accessory Package
17″ Manual Lathe with Accessory Package
17″ Manual Lathe with Accessory Package

Capabilities:
Aluminum, brass, plastics, free machining steel, and other materials

Working Capacity:
This lathe is capable of turning a 3.5″ (90mm) part over the bed. The fact that the lathe will turn to 3.5″ does not mean you can turn a 3.5″ diameter between centers because the crosslide would be in the way. The lathe will turn a part 1.875″ (48mm) over the crosslide. A A .405″ (10mm) diameter hole through the headstock allows long material up to that diameter to be fed through and worked on. This lathe has 17″ between centers.

What’s included:

17″ lathe with hand wheels, 3.1″ 3-jaw self-centering chuck, 3/8″ tailstock drill chuck w/ key, #0 Morse arbor, #1 Morse arbor , with drawbolt, Steady rest, Live Center, Compound Slide,Cutoff Tool and Holder, 3-pc 1/4″ HSS Cutting Tool Set (LH, RH, Boring), 5/32″ T-driver, 3-pc Center Drill Set, Accessories Shop Guide Book, Thread Cutting Attachment

$1,289.00 Add to cart
8″ Manual Lathe with Accessory Package
8″ Manual Lathe with Accessory Package
8″ Manual Lathe with Accessory Package

Capabilities:
Aluminum, brass, plastics, free machining steel, and other materials

Working Capacity:
This lathe is capable of turning a 3.5″ (90mm) part over the bed. The fact that the lathe will turn to 3.5″ does not mean you can turn a 3.5″ diameter between centers because the crosslide would be in the way. The lathe will turn a part 1.875″ (48mm) over the crosslide. A A .405″ (10mm) diameter hole through the headstock allows long material up to that diameter to be fed through and worked on. This lathe has 8″ between centers.

What’s included:

8″ lathe with hand wheels, 2.5″ 3-jaw self-centering chuck, 1/4″ tailstock drill chuck w/ key, #0 Morse arbor, #1 Morse arbor with drawbolt, Steady rest, Live Center, Compound Slide, Cutoff Tool and Holder, 3-pc 1/4″ HSS Cutting Tool Set (LH, RH, Boring), 5/32″ T-driver, 3-pc Center Drill Set, Accessories Shop Guide Book, Thread Cutting Attachment

$1,139.00 Add to cart
Sale!
Premium 2.8 Watt Laser Kit
Premium 2.8 Watt Laser Kit
Premium 2.8 Watt Laser Kit

This is the very popular JTech Photonics 2.8W Laser Kit. JTech Photonics has customized these for MillRight CNC with a cable length appropriate for the Carve King. This will work with the MillRight CNC M3 too. We also add a laser mount … Read More

$350.00 $339.00 Select options
Vacuum Clamping Fixture with Vacuum Generator
Vacuum Clamping Fixture with Vacuum Generator
Vacuum Clamping Fixture with Vacuum Generator

This is a great way to hold down parts by vacuum clamping force. This is everything you need except for a compressor to hold down parts by vacuum. There are two plenum sizes to choose from. Each plenum can clamp down smaller parts as well as parts slightly larger than the plenum itself.

You can hold down woods, plastics, printed circuit boards, sheet metal and metal plates by vacuum power alone!

$184.00 – $299.00 Select options
MillRight CNC M3 Kit
MillRight CNC M3 Kit
MillRight CNC M3 Kit

Product Info

Software is not included but everything you need is available for FREE. See the FAQ page.

Capabilities:
Mills wood, plastic, foam, carbon fiber, circuit boards, and soft metals.

Working Area:
Over 10.25”×10.25”×2”  (260mm × 260mm × 50mm)

NOT included:
Router, router mount, clamps, or end mills. Want a complete hardware solution? See the M3 Bundle here

Shipping:

Shipping on this item is $29 domestic and will be added during check out.

Refund Policy and Product Warranty

Full refunds available for orders that are canceled prior to shipment. We will replace any part that may become defective within 90 days of shipment.

$329.00 – $509.00 Select options
MillRight CNC Carve King Kit
MillRight CNC Carve King Kit
MillRight CNC Carve King Kit

Product Info

Software is not included but everything you need is available for FREE. See the FAQ page.

Capabilities:
Mills wood, plastic, foam, carbon fiber, circuit boards, and soft metals. This machine can make higher precision and more aggressive cuts than our M3.

Working Area:
Approximately 17”×17”×4”

NOT included:
Router, router mount, clamps, or end mills. Want a complete hardware solution? See the Carve King Bundle here

Warranty

There is a 90-day warranty on this product. No returns or cancellations are permitted once the order has left our facility.

We provide free technical support for this product.

 

$699.00 – $869.00 Select options
DeWalt DWP611 Router
DeWalt DWP611 Router
DeWalt DWP611 Router

This DeWalt DWP611 1.25HP variable speed tool is MillRight CNC’s preferred router. Speed range is 16,000 – 27,000 RPM, adjustable by the thumbwheel. 1/4″ collet It’s durable, powerful, and even has LED lights to help you see all the great … Read More

$135.00 Add to cart
1/8″ Collet and Nut for DWP611 or DW618
1/8″ Collet and Nut for DWP611 or DW618
1/8″ Collet and Nut for DWP611 or DW618

The DeWalt DWP611 router comes with a 1/4″ collet that won’t accept 1/8″ cutters. The DeWalt DW618 router comes with a 1/4″ collet and a 1/2″ collet. This precision 1/8″ collet and nut will allow you to hold 1/8″ shank … Read More

$27.50 – $29.95 Select options
Dust Collection Shoe
Dust Collection Shoe
Dust Collection Shoe

This premium dust collection shoe will help keep your work area much cleaner. It mounts directly to your router and the brush ring surrounds the cut area to help contain the dust while your shop vac or dust collector sucks it away.

We offer two different sizes: A shoe for the DWP611 (M3 and Carve King) and one for the DW618 (Power Route).

 

 

$159.00 Select options
400W Spindle Kit
400W Spindle Kit
400W Spindle Kit

Spindle Dimensions

Collet Size: 1/8 inch (3.175mm)

Diameter: 52mm

Length:  185mm

Refund Policy and Product Warranty

60 day warranty from time of shipment.

Full refunds available for any order cancelled prior to shipment.

 

$129.00 Add to cart
Router Mount for DWP611 or Colt
Router Mount for DWP611 or Colt
Router Mount for DWP611 or Colt

We have this hefty aluminum router mount in diameters for the Bosch Colt or DeWalt DWP611. It even has a place to mount a laser module as well. The MillRight CNC M3’s Z plate was designed to accommodate this mount. … Read More

$35.00 Select options
End Mill: 1/4″ 2 Flute
End Mill: 1/4″ 2 Flute

Disclaimer

End mills are consumables. We do not replace or otherwise warranty end mills from chipping, breaking, dulling, or wear.

 

$12.95 Add to cart
Sale!
Spoilboard for MillRight CNC M3
Spoilboard for MillRight CNC M3
Spoilboard for MillRight CNC M3

This spoilboard is used to take the abuse when you cut through your workpiece. It was designed to fit directly on top of the bed of your MillRight CNC M3. It’s made from 3/8″ (about 9.5mm) thick MDF so it … Read More

$17.00 $14.95 Add to cart
Ball Nose End Mill: 1/4″ 2 Flute
Ball Nose End Mill: 1/4″ 2 Flute
Ball Nose End Mill: 1/4″ 2 Flute

Disclaimer

End mills are consumables. We do not replace or otherwise warranty end mills from chipping, breaking, dulling, or wear.

 

$13.45 Add to cart
End Mill: 1/8″ 2 Flute
End Mill: 1/8″ 2 Flute

Disclaimer

End mills are consumables. We do not replace or otherwise warranty end mills from chipping, breaking, dulling, or wear.

$6.50 Add to cart
Ball Nose End Mill: 1/8″ 2 Flute
Ball Nose End Mill: 1/8″ 2 Flute

Disclaimer

End mills are consumables. We do not replace or otherwise warranty end mills from chipping, breaking, dulling, or wear.

$7.95 Add to cart
End Mill: 1/16″ 2 Flute
End Mill: 1/16″ 2 Flute

Disclaimer

End mills are consumables. We do not replace or otherwise warranty end mills from chipping, breaking, dulling, or wear.

$6.50 Add to cart
Vectric Cut2D Desktop
Vectric Cut2D Desktop
Vectric Cut2D Desktop

Vectric Cut2D Desktop is an excellent choice for easy to use yet powerful tools for 2D design and editing PLUS efficient 2D toolpath calculation.

Cut2D can import 2D designs from other programs and also provides a full set of drawing and editing tools. The toolpath options cover all typical 2D routing operations such as Profiling, Pocketing, Auto-Inlays and Drilling. Each toolpath includes options to customize settings and provides a high level of control for different types of operation. All toolpaths can be previewed to show just how the part will look when it is actually cut, allowing toolpaths to be further optimized.

Please note that you do not need this software to run our machines. Many of our customers use Autodesk Fusion 360, which is free to enthusiasts. Cut2D performs many similar tasks, but excels in certain areas compared to Fusion.

$149.00 Add to cart
Vectric VCarve Desktop
Vectric VCarve Desktop
Vectric VCarve Desktop

Vectric VCarve Desktop is an excellent choice for those who are serious about making great signs and general projects.

VCarve Desktop provides a powerful but intuitive software solution for making art, decorations and functional parts with your MillRight CNC machine. There are tools for 2D design and calculation of 2D and 2.5D toolpaths and along with the ability to import and toolpath a single 3D model (STL, OBJ, SKP etc.). There is also support to import multiple Vectric Clip Art 3D models (V3M) to create advanced 3D assemblies.

The software can import 2D designs from other programs but also provides a full set of drawing and editing tools. The toolpath options cover all typical 2D routing operations such as Profiling, Pocketing, Auto-Inlays and Drilling as well as 2.5D strategies such as V-Carving, Prism carving, Moulding Toolpaths, Fluting and even a decorative Texturing strategy. For 3D you can Rough and Finish the model and there are options to project 2D and 2.5D toolpaths onto the 3D surface. Each toolpath includes appropriate options to customize the settings and provide a high level of control for different types of operation. In addition all toolpaths can be previewed to show just how the part will look when it is actually cut, this allows instant feedback to allow toolpaths to be further optimized.

VCarve includes the functionality demanded for complex work while remaining incredibly easy to use and affordably priced. The software is used by wood workers, sign makers, prop makers, plastic fabricators, hobbyists and in many others.

Please note that you do not need this software to run our machines. Many of our customers use Autodesk Fusion 360, which is free to enthusiasts. VCarve performs many similar tasks, but excels in certain areas compared to Fusion.

$349.00 Add to cart
Long USB Cable
Long USB Cable

Your machine kit will come with a short USB cable, but you can replace it with this 54″ (1400mm) long cable so you can park your computer farther away from the machine.   This cable features an inductive choke to help … Read More

$6.95 Add to cart
Digital Caliper
Digital Caliper
Digital Caliper

This a good basic digital caliper that is useful for measuring the thickness of your stock so you can specify the correct cutting depth. It is also great for verifying dimensions when a tape measurer just won’t do. It is made of a composite material, … Read More

$14.95 Read more